Sedigheh Daroumi; Mohammad Ali Aroon; Ramin Yavari; taher yousefi; Hossein Ghasemi mobtaker
Abstract
In this study, the flat sheet membranes including the neat polyethersulfone (PES) and the mixed matrix membranes (MMMs) containing 20 wt. % polyethersulfone (PES) and various amounts of Fe3O4 nanoparticles were prepared using wet phase inversion and conventional casting methods. Manganese ion rejection ...
Read More
In this study, the flat sheet membranes including the neat polyethersulfone (PES) and the mixed matrix membranes (MMMs) containing 20 wt. % polyethersulfone (PES) and various amounts of Fe3O4 nanoparticles were prepared using wet phase inversion and conventional casting methods. Manganese ion rejection and permeate flux as a performance evaluation of the prepared membranes was studied and compared. The characteristics of the fabricated membranes and the synthesized nanoparticles were fulfilled by transmission electron microscopy, field emission scanning electron microscopy and contact angle measurement. The operational parameters such as polymer concentration, pressure, pH, manganese ion concentration and time for manganese ion rejection and permeability were firstly optimized on the neat PES membrane. In the next steps, the performance of the fabricated MMMs containing various amount of Fe3O4 nanoparticles and PES (20%wt.) was evaluated and compared under these optimized conditions. Under the optimal conditions obtained for the rejection of manganese ions by neat PES, the fabricated MMMs had better performance than the neat PES membrane. Also, the results showed that the best performance of the prepared MMMs with the manganese rejection percentage of 89.3% and permeate flux of 28.7 L.m-2.h was found to belong to the PES membranes containing 0.1 wt.% of Fe3O4.
Alireza Nouri; Ramin Yavari; Mohammad Ali Aroon; Taher Yousefi
Abstract
In the present research work, the mixed matrix membranes (MMMs) containing various amount of polyethersulfone (PES) and functionalized multi-walled carbon nanotubes (fMWCNTs) were fabricated and used to investigate the removal of cobalt ions from wastewater by nanofiltration process. Pristine MWCNTs ...
Read More
In the present research work, the mixed matrix membranes (MMMs) containing various amount of polyethersulfone (PES) and functionalized multi-walled carbon nanotubes (fMWCNTs) were fabricated and used to investigate the removal of cobalt ions from wastewater by nanofiltration process. Pristine MWCNTs and fMWCNTs were characterized by Fourier transformed infrared spectroscopy and thermogravimetric analysis. FESEM analysis revealed that the mixed matrix membranes have less surface defects and better membrane performance compared with neat polymeric in the removal of cobalt ions. Permeation test results showed that the MMM containing 22 wt. % PES and 0.6 wt. % fMWCNTs (with outer diameter of 10-20 nm) has the optimum performance from the permeability and cobalt removal point of view. In continuation, the effect of pressure, feed flow rate, cobalt concentration, permeation test time and feed solution pH on the removal of cobalt by selected the MMM was investigated. The obtained results indicated that only pressure has considerable effect on permeation flux. However, all parameters showed different influence on rejection percent of cobalt ions.
Zahra Sarteep; Azadeh Ebrahimian Pirbazari; Mohammad Ali Aroon
Abstract
Hydrothermally synthesized TiO2 nanoparticles containing different amounts of silver were characterized by X-Ray diffraction (XRD), Fourier transform infrared (FT-IR) and scanning electron microscopy equipped with energy dispersive X-ray microanalysis (SEM/EDX) techniques. XRD results showed prepared ...
Read More
Hydrothermally synthesized TiO2 nanoparticles containing different amounts of silver were characterized by X-Ray diffraction (XRD), Fourier transform infrared (FT-IR) and scanning electron microscopy equipped with energy dispersive X-ray microanalysis (SEM/EDX) techniques. XRD results showed prepared samples include 100% anatase phase. The presence of silver in TiO2 nanoparticle network was established by XRD, SEM/EDX and FT-IR techniques. The photocatalytic performance of the prepared catalysts was tested for the degradation of 2,4-dichlorophenol (2,4-DCP) under visible light.. The experiments demonstrated that 2,4-DCP was effectively degraded in the presence of Ag/TiO2 samples. It was confirmed that the presence of Ag on TiO2 catalysts could enhance the photocatalytic degradation of 2,4-DCP in aqueous suspension. It was found that an optimal dosage of 1.68 wt% Ag in TiO2 achieved the fastest 2,4-DCP degradation (95% after 180 min irradiation) under the experimental conditions. On the basis of various characterizations of the photocatalysts, the reactions involved to explain the photocatalytic activity enhancement due to Ag doping include a better separation of photogenerated charge carriers. GC-MS analysis showed the major intermediates of 2,4-DCP degradation are simple acids like oxalic acid, acetic acid, etc. as the final products.