Zahra Mirkazehi; Mohammad Reza Rezaei; Mohammad Sayadi
Abstract
Landfill leachate is the fluid percolating through the landfill and is one of the most important environmental challenges that lead to the contamination of water and soil resources. In this study, magnetic graphene oxide nanoparticles with WO3 (GO-Fe3O4/WO3) were synthesized through the hydrothermal ...
Read More
Landfill leachate is the fluid percolating through the landfill and is one of the most important environmental challenges that lead to the contamination of water and soil resources. In this study, magnetic graphene oxide nanoparticles with WO3 (GO-Fe3O4/WO3) were synthesized through the hydrothermal method to eliminate chemical oxygen demand (COD) from leachate. The obtained products were characterized using X-ray diffraction (XRD), Fourier Transform Infrared Spectroscopy (FTIR), Scanning Electron Microscopy (SEM), Thermogravimetric analysis (TGA), and Vibrating sample magnetometer (VSM) analysis. The influence of various operating parameters, such as initial solution pH, adsorbent dosage, contact time, and temperature, on COD removal was studied. Additionally, kinetic, isotherm, and thermodynamic studies were conducted to evaluate the adsorption capacity of the adsorbent. The results revealed that the maximum adsorption capacity of GO-Fe3O4/WO3 was 2500 mg/g adsorbent at pH 4, a contact time of 90 minutes, an adsorbent dosage of 25 mg g-1, and a temperature below 298 K, respectively. According to the adsorption kinetic fitting results, the experimental adsorption data were well described by the pseudo-second order kinetic with an R2 value of 0.97, and the Freundlich isotherm equation with an R2 value of 0.99. The thermodynamic results indicated that the adsorption was spontaneous and exothermic for COD adsorption. In general, the adsorption process of the synthesized GO-Fe3O4/WO3 nanocomposite revealed that it is highly effective for landfill leachate treatment and has great practical value in leachate treatment.
Mohammad Hossein Sayadi; Elham Chamanehpour; Nazanin Fahoul
Abstract
The widespread use of antibiotics and their subsequent release into the environment has caused concern around the world. Incomplete metabolism releases these chemicals into the environment, and traditional purification systems are unable to remove them. As a result, it lingers in the environment and ...
Read More
The widespread use of antibiotics and their subsequent release into the environment has caused concern around the world. Incomplete metabolism releases these chemicals into the environment, and traditional purification systems are unable to remove them. As a result, it lingers in the environment and is one of the most serious environmental issues confronting public health. The goal of this study was to investigate the possibility of using ultrasonic and titanium dioxide nanoparticles as catalysts for the removal of amoxicillin from aqueous solutions, as well as to figure out the optimal conditions to maximize the efficiency of removal efficiency. Decomposition of amoxicillin in water in the presence of titanium magnetic catalyst with concentrations of 0.1, 0.25, 0.5, 1, and 2.5 g/L and amoxicillin concentrations of 1, 10, 25, 50, and 100 mg/L at different times of 10 to 180 minutes, pHs of 3, 4, 5, 7, 9 and 11, temperatures of 10 to 60 ºC and frequencies of 35, 300, and 700 kHz were examined. At a concentration of 1 g/L catalyst, a concentration of 10 mg/L amoxicillin, a standstill duration of 60 minutes, an acidic pH, a temperature of 40 °C, and a frequency of 35 kHz, the maximum removal of amoxicillin (91.7%) occurred. The use of an ultrasonic method in conjunction with titanium magnetic nanoparticles as an oxidizing agent proved to be a successful tool for lowering amoxicillin concentrations in aqueous media. As a result, advanced oxidation processes, particularly ultrasonic, can reduce pharmaceutical and organic contaminants in the environment.
Reza Jazini Zadeh; Mohammad Sayadi; Mohammad Reza Rezaei
Abstract
The present study was performed on the adsorption of 2,4-Dichlorophenoxyacetic acid from aqueous solutions by amine-modified magnetic nanoparticles. The adsorbent was synthesized by the co-precipitation method. The adsorbent properties of Fe3O4@SiO2-NH2 were investigated using XRD, FTIR, TGA, VSM and ...
Read More
The present study was performed on the adsorption of 2,4-Dichlorophenoxyacetic acid from aqueous solutions by amine-modified magnetic nanoparticles. The adsorbent was synthesized by the co-precipitation method. The adsorbent properties of Fe3O4@SiO2-NH2 were investigated using XRD, FTIR, TGA, VSM and TEM. Adsorbent efficacy was studied by investigating the effect of pH, initial concentration of pollutants, and adsorbent dose, and times. Finally, kinetics equations and isotherms models were used to describe the data. The results showed that the highest removal percentage was observed at pH 6 and the initial concentration 20 mg/l of 2,4-Dichlorophenoxyacetic acid. Adsorption capacity was increased by 65.3% bypassing the time from the beginning of the process to 60 min. The results from the study of isotherms and adsorption kinetics presented that the sorption procedure follows the pseudo-second-order kinetics and the Langmuir isotherm with R2> 99. The maximum adsorption capacity of Fe3O4@SiO2-NH2 is 116.3 mg/g. Besides, thermodynamic studies have shown that the adsorption process in the present study is endothermic and spontaneous. The experiments showed that Fe3O4@SiO2-NH2 synthesized nanoparticles could be an excellent method to remove 2,4- Dichlorophenoxyacetic acid contaminants from the aqueous solutions due to the high efficiency, simplicity, and lack of secondary contamination in the solution.
Atiyeh Yazdani; Mohammad Sayadi; ava Heidari
Abstract
Worldwide studies on contamination levels of anti-inflammatory drugs such as ibuprofen (IBF) show that their concentration in water bodies is increasing. Graphene oxide/palladium nanoparticle (Pd NPs-GO) was synthesized via a simple solvothermal method. The characteristics of the as-prepared samples ...
Read More
Worldwide studies on contamination levels of anti-inflammatory drugs such as ibuprofen (IBF) show that their concentration in water bodies is increasing. Graphene oxide/palladium nanoparticle (Pd NPs-GO) was synthesized via a simple solvothermal method. The characteristics of the as-prepared samples were examined using X-ray fluorescence, scanning electron microscopy, and Fourier transforms infrared spectroscopy. The performance of Pd NPs-GO nanocomposite as a sonocatalyst was evaluated for the degradation of IBF under ultrasonic irradiation (35 kHz), and compared with graphene (GO) and palladium nanoparticle (Pd NPs). Some influencing parameters such as IBF initial concentration, pH, catalyst dosage, and irradiation time were investigated. The findings showed that Pd NPs-GO nanocomposite exhibited higher sonocatalyst activity for IBF than other catalysts. A higher ibuprofen degradation efficiency was observed in lower pH (3), lower initial concentration (30 mg/L), higher catalyst dosage (2 g/L), and higher ultrasonic irradiation time (50 min). The kinetics of the degradation of IBF followed pseudo-first-order reaction kinetics.
Atiyeh Yazdani; Mohammad Sayadi; Ava Heidari
Abstract
The green synthesis of palladium oxide nanoparticles using Dictyota indica seaweed extract was investigated. Dictyotales is a large order in the brown algae (class Phaeophyceae). The color of the reaction mixture changed which indicated the formation of palladium oxide nanoparticles. UV-Visible, SEM, ...
Read More
The green synthesis of palladium oxide nanoparticles using Dictyota indica seaweed extract was investigated. Dictyotales is a large order in the brown algae (class Phaeophyceae). The color of the reaction mixture changed which indicated the formation of palladium oxide nanoparticles. UV-Visible, SEM, TEM, XRD, and FTIR analysis determined the characteristics of synthesized nanoparticles. The UV-Visible analysis showed the formation of palladium oxide nanoparticles. SEM and TEM analyses presented the palladium oxide nanoparticles have a spherical shape and based on DLS analysis with the average particle diameter of 19nm. The comparisons of the nanoparticle size with different biological synthesis were studied which revealed this methodology offer smallest size. The crystallographic parameters of the synthesized Pd nanoparticles were as follows: crystalline structure (cubic), space group (Fm-3m), and lattice parameter (a=5.6500, b=5.6500, c=5.6500, α=90, β=90, and γ=90). FTIR analysis indicated the presence of a palladium oxide group in the product. The removal efficacy of cadmium by the palladium oxide nanoparticles was investigated to optimize the pH, contact time, dose of adsorbent and concentration of cadmium. The results showed that optimum conditions for cadmium removal from water were obtained at pH 8, 500 mg/l adsorbent dose and 20 min contact time, wherein in these circumstances the removal of cadmium was 82.82%. The adsorption isotherms primacy was as follows, Langmuir R2=0.9904> Freundlich R2=0.9857> Temkin R2=0.8791.
Farzaneh Arsiya; Mohammad Sayadi; Sara Sobhani
Abstract
The presence of Arsenic in drinking water is the greatest threat to health effects especially in water. The purpose of this study is application of green palladium nanoparticles for removal of trivalent Arsenic from aqueous solutions and also the impact of some factors such as retention time, pH, concentration ...
Read More
The presence of Arsenic in drinking water is the greatest threat to health effects especially in water. The purpose of this study is application of green palladium nanoparticles for removal of trivalent Arsenic from aqueous solutions and also the impact of some factors such as retention time, pH, concentration of palladium nanoparticles and Arsenic concentrations was studied. The values for Arsenic removal from aqueous solutions were measured by furnace atomic adsorption spectrometry (Conter AA700). In the study, Langmuir and Freundlich isotherm models and pseudo-second order kinetic model were studied. The results of optimization is shown that 0.5 g of nanoparticles can removed %99.8 of Arsenic with initial concentration of 0.5 g/l, in 5 minutes at pH=4. Langmuir model, Freundlich model (R2=0.94) and pseudo-second order kinetic model (R2=0.99) shown high correlation for removing of Arsenic from aqueous solutions. It was found, palladium nanoparticles can be used as an efficient method to remove Arsenic from aqueous solutions in a short time.